
Engine Technology – Petrol Engines
Everything you need to know about preparing, starting, breaking in, tuning and maintaining your Zenoah or Chung Yang two-stroke engine.
Written and compiled by Harrie Schiks, owner of TPS Racing BV, based on many years of practical experience with RC petrol engines, engine tuning and competitive racing.
Click on a chapter and then select the topic you want to read.
1. Preparing a New Cylinder Kit & Engine
1.1 Checks Before Starting the Engine for the First Time
A new petrol engine should be carefully checked before its first start. This helps prevent problems caused by incorrect installation or fuel supply rather than by the engine itself.
- Check that the engine is securely mounted.
- Check that the clutch and complete drivetrain can move freely.
- Check the mounting of the carburettor, insulator and air filter.
- Check that the exhaust is securely fitted and has no leaks.
- Inspect the fuel lines for kinks, damage and leaks.
- Check that the throttle opens fully and reliably returns to the closed position.
- Check that the engine kill switch operates correctly.
- Make sure cooling air can flow freely around the cylinder.
1.2 Fuel Tank and Tank Ventilation
The engine and carburettor must be able to draw sufficient fuel during operation. The fuel tank must therefore be properly vented.
If the tank vent becomes blocked, a vacuum can develop inside the tank. This restricts the fuel supply and may cause the engine to run poorly or stop.
Many standard fuel tank caps contain a rubber valve for tank ventilation. In practice, this valve often does not work sufficiently or may fail completely. We therefore recommend fitting the ventilation kit mentioned below.
- Check the fuel tank ventilation regularly.
- Avoid kinks in ventilation and fuel lines.
- Make sure the fuel filter inside the tank is clean.
- Check that all connections are secure and leak-free.
1.3 Air Filter and Spark Plug
A good air filter protects the cylinder, piston and piston ring against dirt and dust. Check that the filter is clean and correctly installed. Off-road applications require more intensive filtration than on-road applications.
Also check the engine kill switch, spark plug and spark plug cap. Damaged components must be replaced immediately.
2. Starting the Engine Correctly
2.1 Preparation Before the First Start
Place the RC car on a stable, safe surface and make sure the driven wheels are always raised clear of the ground.
- Fill the tank with fresh, correctly mixed fuel.
- Check the fuel lines and tank ventilation.
- Switch on the transmitter and receiver.
- Check the throttle operation and engine kill switch.
2.2 Starting a Cold Engine
When starting a cold engine, the carburettor must be filled with fresh fuel. Press the primer bulb on the carburettor 4 to 6 times to ensure sufficient fuel is supplied.
2.2.1 Carburettor with Choke
- Make sure the driven wheels are raised clear of the ground.
- Keep the throttle completely closed.
- Close the choke.
- Pull the recoil starter 1 to 3 times until the engine briefly fires.
- Fully open the choke again.
- Pull the recoil starter again until the engine starts.
2.2.2 Carburettor without Choke
- Make sure the driven wheels are raised clear of the ground.
- Fully open the throttle.
- Slowly pull the recoil starter 4 to 6 times.
- Close the throttle completely again.
- Pull the recoil starter another 1 to 3 times until the engine starts.
2.3 Restarting a Warm Engine
A warm engine normally does not require the choke. Therefore, first try starting the engine with the choke open.
2.4 What Should You Do if the Engine Does Not Start?
- Check whether the spark plug produces a spark. If in doubt, fit a new spark plug.
- Open the fuel tank cap and listen for a hissing sound caused by vacuum or pressure inside the tank. View Fuel Tank Ventilation Kit TPS0710/10.
- Check whether fuel is reaching the carburettor.
- Check whether the choke is correctly positioned.
- Check whether the spark plug has become wet due to excess fuel.
- Check the carburettor settings and the overall condition of the engine.
If the engine still has difficulty starting, also check the compression and condition of the piston ring.
VIEW CHAPTER 6.4 – CHECKING THE PISTON RING3. Breaking In a New Cylinder Kit & Engine
3.1 Why Must a New Cylinder Kit or Engine Be Broken In?
During the break-in process, the contact surfaces of the piston ring and cylinder gradually adapt to each other.
The engine must receive sufficient lubrication and should not become unnecessarily hot. Correct carburettor adjustment is therefore important.
3.2 The First Tank of Fuel
First allow the engine to gradually reach operating temperature. Then begin with short driving sessions at low to medium load.
- Vary the engine speed regularly.
- Avoid extended full-throttle driving.
- Avoid prolonged high engine speeds without load.
- Regularly check for unusual engine noises.
- Monitor the engine temperature.
Allow the engine to cool down between runs if the temperature rises excessively.
VIEW CHAPTER 4 – FUEL & MIXING RATIO3.3 Gradually Increasing the Load
When the engine responds well and the temperature remains under control, the load can gradually be increased.
Avoid extended full-throttle driving during the initial operating period. Regularly check that the engine accelerates smoothly and is not running too lean.
3.4 Carburettor Adjustment During Break-In
An excessively lean carburettor setting can increase engine temperature and cause damage. During break-in, therefore, ensure a safe setting with sufficient fuel and lubrication.
Further information about the L needle, H needle and temperature checks can be found in Chapter 5.
VIEW CHAPTER 5 – CARBURETTOR ADJUSTMENT4. Fuel & Mixing Ratio
4.1 Which Petrol Should You Use?
For the two-stroke petrol engines covered by this TPS Racing guide, we recommend fresh, high-quality petrol, preferably E5.
Do not use old or contaminated fuel. Store petrol in a suitable, tightly sealed fuel container.
In addition to regular pump petrol, alkylate petrol such as Aspen is also available. The differences and important considerations are explained in Chapter 4.5.
VIEW CHAPTER 4.5 – ASPEN ALKYLATE PETROL4.2 PSR2 Two-Stroke Mixing Oil
A two-stroke engine requires oil mixed with the petrol. This oil lubricates the piston, cylinder, crankshaft bearings and other moving components.
TPS Racing recommends PSR2 Two-Stroke Mixing Oil for this application.
4.3 Mixing Ratio 1:25 – How Much Oil Should You Add?
With a mixing ratio of 1:25, you use 40 ml of two-stroke oil per litre of petrol.
| Petrol Quantity | PSR2 Oil Quantity |
|---|---|
| 1 litre | 40 ml |
| 2 litres | 80 ml |
| 3 litres | 120 ml |
| 4 litres | 160 ml |
| 5 litres | 200 ml |
4.4 Mixing and Storing Fuel
- Use a clean, suitable fuel container.
- Measure the required amount of petrol.
- Add the correct amount of two-stroke oil.
- Close the container and mix the fuel thoroughly.
- Preferably use freshly mixed fuel.
Always follow the engine manufacturer's instructions before use. The mixing ratio stated here is the TPS Racing recommendation for the engines and applications described.
4.5 Aspen Alkylate Petrol
What is Aspen?
Aspen is a special type of alkylate petrol that produces less odour than regular petrol. Aspen is mainly used in small garden machinery such as chainsaws and brush cutters. Their engine speeds rarely exceed 13,000 rpm. This is a very important point!
Advantages
- Less petrol odour.
- Fewer deposits in the engine and exhaust.
Disadvantages
- Not every two-stroke oil mixes well with Aspen.
- The carburettor may need to be readjusted.
- May result in higher fuel consumption.
- Not every type of Aspen is suitable for standard RC engines, especially tuned engines.
Which Aspen Should You Use?
| Fuel | TPS Racing Recommendation |
|---|---|
| Aspen 2 Contains 2% oil (1:50) | Not recommended. |
| Aspen 4 Contains no oil | Not recommended. |
| Aspen R Racing petrol | May be suitable with 4% PSR2 Race Oil (1:25), provided the oil mixes properly with the fuel. |
5. Carburettor Adjustment
5.1 Preparation and Basic Settings
Choose a safe location with sufficient open space. Make sure the driven wheels can rotate freely.
Start with the following basic settings:
| Adjustment | What Should You Do? |
|---|---|
| Idle Speed Screw | Carefully turn the idle speed screw fully in, then turn it out 2 turns. |
| L Needle | Carefully turn the L needle fully in, then turn it out 1¼ turns. |
| H Needle | Carefully turn the H needle fully in, then turn it out 1¼ turns. |
5.2 Adjusting the Idle Speed and L Needle Together
Start the engine and let it idle for 1 to 2 minutes. Then briefly apply full throttle.
The engine should respond immediately and accelerate without hesitation.
Result 1 – The Engine Hesitates When Accelerating and Does Not Reach Speed
What Should You Do?
Turn the L needle slightly clockwise (in = leaner) and the idle speed screw slightly anticlockwise (out = more air).
Repeat the procedure until the engine responds smoothly to the throttle.
Result 2 – The Engine Sounds Hollow and the RPM Hangs
What Should You Do?
Turn the L needle slightly anticlockwise (out = richer) and the idle speed screw slightly clockwise (in = less air).
Repeat the procedure until the engine responds smoothly to the throttle.
5.3 Adjusting the H Needle
The H needle controls the fuel supply at higher engine speeds, from approximately 8,000 rpm.
Drive for a short distance at half throttle and then apply full throttle. Listen carefully to the engine sound.
Result 1 – The Engine Sputters and Sounds Too Rich
What Should You Do?
Turn the H needle slightly clockwise (in = leaner).
Repeat the procedure until the engine sounds consistent and revs smoothly.
Result 2 – The Engine Sounds Hollow and Refuses to Rev Up
What Should You Do?
Turn the H needle slightly anticlockwise (out = richer).
Repeat the procedure until the engine sounds consistent and revs smoothly.
Important Information:
5.4 Measuring Engine Temperature
The correct engine temperature is important for performance, reliability and service life.
TPS Racing measures the temperature on the intake side, approximately in the middle of the engine crankcase.
At this measuring point, TPS Racing uses approximately 60 to 70°C as a practical guideline.
6. Piston Ring Wear and Maintenance
6.1 Why Is the Piston Ring So Important?
The piston ring provides a seal between the piston and cylinder wall. This seal is necessary for good compression and reliable operation of the engine and carburettor.
As the piston ring wears, compression may decrease. This can cause starting problems, irregular engine operation and loss of power.
6.2 How Does Piston Ring Wear Develop?
A new piston ring has rounded upper and lower edges on its contact surface. This shape ensures controlled contact with the cylinder wall.
During operation, a very narrow, horizontal, shiny metallic strip initially appears on the originally black running surface.
The longer the piston ring is used, the wider this shiny strip becomes. At the same time, the rounded contact edges may gradually become sharper.
With severe wear, these edges may eventually become very sharp. The piston ring end gap may also increase.
Separately, wear can develop in the piston ring groove. This allows the piston ring to move further up and down within the groove.
These forms of wear may cause poorer sealing, additional cylinder wear and, in the worst case, engine damage.
6.3 When Should the Piston Ring Be Replaced?
Based on many years of practical experience and competitive racing, TPS Racing uses the following preventive maintenance intervals.
| Maintenance Interval | Fuel Consumption |
|---|---|
| First replacement | After approximately 6 to 8 litres |
| Second replacement | After a further 8 to 15 litres |
| Subsequent replacements | Approximately every 15 litres |
Each interval is calculated from the previous piston ring replacement.
These are practical TPS Racing guidelines rather than universally applicable replacement intervals. The actual condition of the piston ring remains the deciding factor.
6.4 Inspecting the Piston Ring Through the Exhaust Port
Piston ring wear can be visually inspected through the exhaust port without completely removing the cylinder.
- Allow the engine to cool completely. Never inspect a hot or running engine.
- Remove the exhaust. Make sure no dirt enters the exhaust port.
- Carefully rotate the engine by hand. Position the piston so the piston ring is visible through the exhaust port.
- Use sufficient lighting. Examine the horizontally positioned piston ring.
- Inspect the shiny contact surface. Check how wide the horizontal, shiny metallic strip on the black piston ring has become.
- WARNING! The piston ring must be replaced once it reaches the condition shown in Picture 2. Do not wait any longer!
- Compare the wear with the illustration below.

How Can You Recognise the Different Stages of Wear?
Picture 1 – New Piston Ring
The piston ring is mostly black. Only a very narrow, horizontal, shiny metallic strip is visible in the centre of the running surface. The piston ring is in good condition and does not yet need replacing.
Picture 2 – Partially Worn Piston Ring
The horizontal shiny strip has become noticeably wider. A larger part of the originally black running surface is now metallic and shiny. The piston ring must be replaced to avoid engine damage!
Picture 3 – Severely Worn Piston Ring – REPLACE immediately!
The visible running surface has become completely shiny and metallic. According to the TPS Racing maintenance method, this is a clear indication that the piston ring must be replaced immediately. Also inspect the piston, piston ring groove and cylinder.
Important: The width of the shiny strip is a practical visual indication and not an exact wear measurement. If in doubt, also inspect the piston ring end gap, piston ring groove and cylinder condition.
7. Spark Plugs & Performance Spark Plugs
7.1 The Function of the Spark Plug
The spark plug produces the spark that ignites the fuel-air mixture inside the cylinder.
A properly functioning spark plug is important for reliable starting, smooth engine operation and efficient combustion.
7.2 Inspecting the Spark Plug
Allow the engine to cool completely before removing the spark plug.
- Carefully remove the spark plug cap.
- Clean the area around the spark plug.
- Unscrew the spark plug using a suitable tool.
- Inspect the electrode for wear and damage.
- Check for contamination, oil deposits or signs of overheating.
- Install the correct spark plug according to the engine specifications.
Carbon Fouling – Dry Carbon Deposits on the Spark Plug
Carbon fouling refers to dry, black, soot-like carbon deposits on the spark plug insulator tip and electrodes. These deposits can weaken the ignition spark and/or form a conductive layer between the ceramic insulator and the inside of the spark plug body. As a result, the engine may become difficult to start, run irregularly, misfire or stop. This may mean that the spark plug produces a good spark outside the engine but fails to produce a spark at the electrode tip under pressure inside the engine.
How Can You Recognise Carbon Fouling?
The ceramic part of a spark plug is normally white. In a correctly adjusted engine, it often develops a coffee-brown colour. If the ceramic has a dry, black, soot-like coating, this indicates carbon fouling. This differs from a wet, oily spark plug, where fuel or oil is visibly present.
Possible Causes:
- An excessively rich carburettor setting.
- An incorrect fuel-to-oil mixing ratio.
- Incomplete combustion of the fuel-air mixture.
- A spark plug with an unsuitable heat range.
- Excessive oil deposits caused by incomplete combustion.
- Wear of the piston, piston ring and/or cylinder.
What Should You Do?
- Check the carburettor adjustment and condition of the air filter.
- Check that the correct spark plug with the appropriate heat range is fitted.
- Check the engine compression and overall condition.
- Inspect the exhaust for excessive contamination.
- Replace a heavily contaminated spark plug.
- Inspect the spark plug appearance again after driving.
7.3 Standard Spark Plugs and Iridium Performance Spark Plugs
In addition to standard spark plugs, iridium performance spark plugs are also available.
An iridium spark plug features a fine iridium centre electrode that is particularly resistant to wear. Depending on the application, this can contribute to reliable spark formation and a longer service life.
However, an iridium spark plug does not automatically increase engine power.
7.4 When Should the Spark Plug Be Replaced?
Inspect the spark plug regularly, particularly if the engine is difficult to start or runs irregularly.
Replace the spark plug if there is noticeable wear, damage, defective insulation or an unreliable ignition spark.
© 2026 Harrie Schiks – TPS Racing BV. All Rights Reserved.
Author: Harrie Schiks. The original texts, parts of the texts, technical explanations, illustrations and other content on this page are protected by copyright.
Without prior written permission from Harrie Schiks, it is prohibited to copy, reproduce, publish, distribute, modify or commercially use this content, in whole or in part, except where permitted by applicable law.


